Skip to main content
Re-opening to in-store shopping on Feb 16, 2021. Please check opening hours before visiting the store.
Due to a significant increase in product orders and requests, a timely response to phone and emails is being delayed.  We appreciate your patience and will respond as soon as possible. 
We will not be renting XC equipment this winter season.

Filter By:

Clearance Race Wax

Vauhti Blackfox Block -2...-20
$85.00 $170.00 50% Off
A block for dry and severe cold conditions BlackFox performs well in severe cold even with low humidity . The operating range is wider when the snow is dirty. Use either an SF or HF series Blue or Green glider as a basewax for the GoldFox powder. Application: Hot application with an iron: Apply an even layer of the desired compressed fluor on the glide surfaces. Bind the layer of concentrate to the base with quick strokes of the iron. After light ironing, spread another layer and bind again with light strokes of the iron. Spread a third layer and iron on the same way as a powder. Using this method will get enough product on the bases and the actual ironing can take place safely without harming the ski. The end result is very close to a powder application. Iron the concentrate in wet conditions without a Teflon sheet in such a way that the product melts completely. In humid below freezing conditions use a Teflon sheet. This causes the glide surface to become “greasier”. Always apply a cold rubbed final layer in dry, cold, below freezing conditions. Cold rubbed application: Rub or “crayon” on a layer to the glide surfaces of your skis. Use a natural cork with sufficient force so that the compressed fluor on the ski base becomes shiny. This takes about 2-3 minutes of corking per ski. Let the skis cool for a few minutes and then nylon brush. Repeat this step if the distance to be skied is long, or if the snow surface is abrasive, or if the ski bases are in bad condition and have not been adequately stone ground or sanded. The corking can also be done with a rotocork. Before you begin, make sure that the cork is clean. If using a roto cork, keep rpms low and use very light pressure – take care not to brush too much. Tips for working with compressed fluor gliders: - A thin cold rubbed compressed fluor layer fine tunes and improves performance in nearly all below freezing conditions. - If you want to alter a powder's working range, do it with a layer of fluor concentrate before applying the powder: For example a layer of Zero compressed fluor block followed by the Gold powder. This improves the moisture tolerance of the Gold powder. - If you are not an experienced fluor product user, use cold rubbed compressed fluor layers as the top coats. This maximizes your chances of achieving the best possible performance.
Vauhti Blackfox High Fluor Powder -2...-20
$100.00 $200.00 50% Off
A powder for dry and severe cold conditions BlackFox performs well in severe cold even with low humidity . The operating range is wider when the snow is dirty. Use either an SF or HF series Blue or Green glider as a basewax for the GoldFox powder. Application: Cold: Sprinkle the powder on the glide surfaces. Rub the powder either with a manual hand cork or a rotocork until it forms an even, smooth layer on the glide surfaces. With a rotocork apply only light pressure. Let the powder cool and then finish with a brush matched to the conditions. If needed, the application can be repeated by corking the powder dust generated by the brushing over again. Always complete the application with a thorough brushing. Hot: Sprinkle the powder and rub lightly using a natural cork ensuring an even spread throughout the glide surfaces. A light rubbing of the powder prior to ironing is a requirement for a successful application. Without the initial rubbing, the graphite contained in the powder will not sufficiently spread into an even layer resulting in reduced overall performance. Use a mild iron setting, approximately 110°C as the powder does not need to fully melt. Cool the bases thoroughly and brush vigorously to finish.
Vauhti Fox 10F Hardener Powder 35g
$21.00 $42.00 50% Off
Hardening powders are designed for conditions in which the track or the skating surface is exceptionally abrasive. For example, on artificial snow or especially when the snow re-freezes after a long period of thaw. In comparison to plain conventional or fluor glide waxes, using the hardening powder additives in icy snow conditions, results in superior durability and abrasion resistance.
Vauhti Fox 20F Hardener Powder 35g
$21.00 $42.00 50% Off
Hardening powders are designed for conditions in which the track or the skating surface is exceptionally abrasive. For example, on artificial snow or especially when the snow re-freezes after a long period of thaw. In comparison to plain conventional or fluor glide waxes, using the hardening powder additives in icy snow conditions, results in superior durability and abrasion resistance.
Vauhti Foxgel Minus 35g -5...-15
$84.99 $169.99 50% Off
Waxing instructions: Apply the emulsion on the glide surfaces to a maximum 1 meter length at a time and immediately spread it into a thin film. Foxgel Minus is thicker than Foxgel Wet, which is why on the kick zone it decreases the grip slightly. Use this product for coating grip waxes and klisters only when grip waxing is over gripping and it is necessary to reduce the grip. Notice! Remember to brush carefully with nylon brush a ski waxed with Fox Gel Minus.
Vauhti LF Cold Race Glide Wax
$39.00 $78.00 50% Off
Operating range: +10/-1°C | 50/30°F Comparable by hardness and wax composition to HF WET. Operating range of LF RACE WET goes down to -3°C on fresh snow and down to -5°C on old snow. A good choice on sunny spring weather when the snow humidity variates for wet to dry. The series is intended specifically for active skiers and competitive skiers for training rounds. Fluorinated products are suitable for all snow types and weather conditions. The content of these products is the same as their predecessor Vauhti LF RACE-gliders except LF RACE MID.
Vauhti MF1 Medium Fluor Powder +10...-2
$67.50 $135.00 50% Off
Molybden Fluor Powder, suitable for wet conditions and temperatures just below freezing, -2...-3°C. It is easy to use, even without previous experience of fluor powders. A wax powder in MF-1 protects ski bases from overheating, and the ski bases do not "dry up" as easily as with high fluor powders. Molybden in the powder effectively reduces dirt contamination Application: Use HF or LF wax, appropriate for the quality of snow and humidity, as a base wax. Very carefully brush the layer of wax that will be under the layer of powder with a nylon brush. Make sure you brush it sufficiently with a brass or stainless steel brush. The importance of carefully brushing base waxes is especially evident in conditions around the freezing point and in wet conditions. Polish the bottom of the skis before applying the powder. Iron the powder using the maximum temperature on the waxing iron (Vauhti waxing iron). Cool the ironed area and carefully brush it with a nylon brush. If the snow is clingy or very dirty, then finish off the brushing with a few, light, powder-brass or -stainless steel strokes.
Vauhti Silver G Block -0.5...+15
$80.00 $160.00 50% Off
A specialty block with a graphite additive for near freezing and wet conditions The improved composition of Silverfox G is much harder and wear resistant than the regular white Silverfox. The optimal working range is coarse wet conditions and in general, all wet conditions where the snow is dirty. The working range extends below freezing to about -1°C on new moist snow and on old snow to about -3°C. Application: Hot application with an iron: Apply an even layer of the desired compressed fluor on the glide surfaces. Bind the layer of concentrate to the base with quick strokes of the iron. After light ironing, spread another layer and bind again with light strokes of the iron. Spread a third layer and iron on the same way as a powder. Using this method will get enough product on the bases and the actual ironing can take place safely without harming the ski. The end result is very close to a powder application. Iron the concentrate in wet conditions without a Teflon sheet in such a way that the product melts completely. In humid below freezing conditions use a Teflon sheet. This causes the glide surface to become “greasier”. Always apply a cold rubbed final layer in dry, cold, below freezing conditions. Cold rubbed application: Rub or “crayon” on a layer to the glide surfaces of your skis. Use a natural cork with sufficient force so that the compressed fluor on the ski base becomes shiny. This takes about 2-3 minutes of corking per ski. Let the skis cool for a few minutes and then nylon brush. Repeat this step if the distance to be skied is long, or if the snow surface is abrasive, or if the ski bases are in bad condition and have not been adequately stone ground or sanded. The corking can also be done with a rotocork. Before you begin, make sure that the cork is clean. If using a roto cork, keep rpms low and use very light pressure – take care not to brush too much. Tips for working with compressed fluor gliders: - A thin cold rubbed compressed fluor layer fine tunes and improves performance in nearly all below freezing conditions. - If you want to alter a powder's working range, do it with a layer of fluor concentrate before applying the powder: For example a layer of Zero compressed fluor block followed by the Gold powder. This improves the moisture tolerance of the Gold powder. - If you are not an experienced fluor product user, use cold rubbed compressed fluor layers as the top coats. This maximizes your chances of achieving the best possible performance.
Vauhti Silver G High Fluor Powder -0.5...+15
$100.00 $200.00 50% Off
A specialty powder with a graphite additive for near freezing and wet conditions The improved composition of Silverfox G is much harder and wear resistant than the regular white Silverfox. The optimal working range is coarse wet conditions and in general, all wet conditions where the snow is dirty. The working range extends below freezing to about -1°C on new moist snow and on old snow to about -3°C. Application: Cold: Sprinkle the powder on the glide surfaces. Rub the powder either with a manual hand cork or a rotocork until it forms an even, smooth layer on the glide surfaces. With a rotocork apply only light pressure. Let the powder cool and then finish with a brush matched to the conditions. If needed, the application can be repeated by corking the powder dust generated by the brushing over again. Always complete the application with a thorough brushing. Hot: Sprinkle the powder and rub lightly using a natural cork ensuring an even spread throughout the glide surfaces. A light rubbing of the powder prior to ironing is a requirement for a successful application. Without the initial rubbing, the graphite contained in the powder will not sufficiently spread into an even layer resulting in reduced overall performance. Use a mild iron setting, approximately 110°C as the powder does not need to fully melt. Cool the bases thoroughly and brush vigorously to finish.
Vauhti Silver Liquid 0...+15
$92.50 $185.00 50% Off
A liquid fluor finishing additive for very wet conditions with dirty snow- Application: 1. On top of bases prepared with fluor powder or compressed fluor glides: Shake the bottle well prior to application. Spread a thin, even layer of the liquid on top of a brushed, room temperature fluor waxed ski base. Let dry for at least five minutes and brush the coating with a nylon brush. A longer drying time will add and enhance the durability and wear resistance of the waxing. 2. On top of non or low fluor glide waxes: Shake the bottle well prior to application. Spread a thin, even layer of the liquid on top of a waxed and brushed ski base. Let dry for 3-4 minutes. Spread a second thin layer and let dry for at least five minutes. Rub the dried coating vigorously with a natural cork. The best results are achieved with a mechanical rotocork. When the bases have cooled off completely finish off with a nylon brush. A longer drying time will add and enhance the durability and wear resistance of the waxing.
Vauhti Silverfox Wet Block 0...+15
$80.00 $160.00 50% Off
A specialty block for drenched, thoroughly wet conditions The composition of Silverfox is improved for performance in very wet conditions. The optimal range extends from slushy wet to wet and sticky conditions around the freezing point. SilverFox is not recommend when the temperature is colder than the freezing point. It is also not recommended for use in dirty snow. Application: Hot application with an iron: Apply an even layer of the desired compressed fluor on the glide surfaces. Bind the layer of concentrate to the base with quick strokes of the iron. After light ironing, spread another layer and bind again with light strokes of the iron. Spread a third layer and iron on the same way as a powder. Using this method will get enough product on the bases and the actual ironing can take place safely without harming the ski. The end result is very close to a powder application. Iron the concentrate in wet conditions without a Teflon sheet in such a way that the product melts completely. In humid below freezing conditions use a Teflon sheet. This causes the glide surface to become “greasier”. Always apply a cold rubbed final layer in dry, cold, below freezing conditions. Cold rubbed application: Rub or “crayon” on a layer to the glide surfaces of your skis. Use a natural cork with sufficient force so that the compressed fluor on the ski base becomes shiny. This takes about 2-3 minutes of corking per ski. Let the skis cool for a few minutes and then nylon brush. Repeat this step if the distance to be skied is long, or if the snow surface is abrasive, or if the ski bases are in bad condition and have not been adequately stone ground or sanded. The corking can also be done with a rotocork. Before you begin, make sure that the cork is clean. If using a roto cork, keep rpms low and use very light pressure – take care not to brush too much. Tips for working with compressed fluor gliders: - A thin cold rubbed compressed fluor layer fine tunes and improves performance in nearly all below freezing conditions. - If you want to alter a powder's working range, do it with a layer of fluor concentrate before applying the powder: For example a layer of Zero compressed fluor block followed by the Gold powder. This improves the moisture tolerance of the Gold powder. - If you are not an experienced fluor product user, use cold rubbed compressed fluor layers as the top coats. This maximizes your chances of achieving the best possible performance.
Vauhti Silverfox Wet High Fluor Powder 0...+15
$100.00 $200.00 50% Off
A specialty powder for drenched, thoroughly wet conditions The composition of Silverfox is improved for performance in very wet conditions. The optimal range extends from slushy wet to wet and sticky conditions around the freezing point. SilverFox is not recommend when the temperature is colder than the freezing point. It is also not recommended for use in dirty snow. Application: Does not require any special considerations/techniques. It can be ordinarily rubbed on cold or ironed. When ironing on, use a temperature setting where the product melts completely – approximately 120 -130°C.
Vauhti Zerofox Block +2...-4
$85.00 $170.00 50% Off
A block for mild, below freezing conditions The composition of ZeroFox is also improved. It is harder than its predecessor and its optimal working range is broader. The powder also tolerates dry snow substantially better than the previous version. The improved working range extends, under normal humidity, from freezing all the way down to -5 to -8°C. Application: Hot application with an iron: Apply an even layer of the desired compressed fluor on the glide surfaces. Bind the layer of concentrate to the base with quick strokes of the iron. After light ironing, spread another layer and bind again with light strokes of the iron. Spread a third layer and iron on the same way as a powder. Using this method will get enough product on the bases and the actual ironing can take place safely without harming the ski. The end result is very close to a powder application. Iron the concentrate in wet conditions without a Teflon sheet in such a way that the product melts completely. In humid below freezing conditions use a Teflon sheet. This causes the glide surface to become “greasier”. Always apply a cold rubbed final layer in dry, cold, below freezing conditions. Cold rubbed application: Rub or “crayon” on a layer to the glide surfaces of your skis. Use a natural cork with sufficient force so that the compressed fluor on the ski base becomes shiny. This takes about 2-3 minutes of corking per ski. Let the skis cool for a few minutes and then nylon brush. Repeat this step if the distance to be skied is long, or if the snow surface is abrasive, or if the ski bases are in bad condition and have not been adequately stone ground or sanded. The corking can also be done with a rotocork. Before you begin, make sure that the cork is clean. If using a roto cork, keep rpms low and use very light pressure – take care not to brush too much. Tips for working with compressed fluor gliders: - A thin cold rubbed compressed fluor layer fine tunes and improves performance in nearly all below freezing conditions. - If you want to alter a powder's working range, do it with a layer of fluor concentrate before applying the powder: For example a layer of Zero compressed fluor block followed by the Gold powder. This improves the moisture tolerance of the Gold powder. - If you are not an experienced fluor product user, use cold rubbed compressed fluor layers as the top coats. This maximizes your chances of achieving the best possible performance.
Vauhti Zerofox High Fluor Powder +2...-4
$100.00 $200.00 50% Off
A powder for mild, below freezing conditions.The composition of ZeroFox is also improved. It is harder than its predecessor and its optimal working range is broader. The powder also tolerates dry snow substantially better than the previous version. The improved working range extends, under normal humidity, from freezing all the way down to -4°C. Application: Does not require any special considerations/techniques. It can be rubbed on cold or ironed on normally. Use an iron temperature between 130-140°C to ensure complete melting of the powder.
Vauhti hfC21 Gel -6...-20
$84.99 $169.99 50% Off
Vauhti hfC9.1 High Fluor Carbon Powder +10...-3
$115.00 $230.00 50% Off
Vauhti product development team makes continuous innovations and has improved the FC products to a high level. These products have superb characteristics. They minimize the surface energy of the ski base, making it super-hydrophobic and dirt-repelling. At the same time, they are excellent in cold conditions to reduce dry friction. The speed, glide sensitivity, and durability of the FC-powders are excellent in all weather conditions. With versatile application methods every skier will benefit, even the lightweight skiers.
Toko HB-004 100% Fluoro Powder
$92.49 $184.99 50% Off
This 100% pure FluoroCarbon powder is a very universal powder, which is part of the Toko racing program. Contents: 30 g
Toko HF 120g AX134
$82.49 $164.99 50% Off
A high fluoro special-purpose wax, AX134 is especially soft for extremely warm, wet conditions.
Toko HF Glide
$36.99 - $82.49 $73.99 - $164.99 50% Off
PRODUCT DESCRIPTION Highly fluorinated racing wax to meet the highest demands. The wax used by World Cup stars! Features: •Tribloc technology for perfect sliding properties •Very high fluorine content for maximum water and dirt repellency •Unmatched degree of hold •Fluorine Dibloc acts as a bonding agent for Top Finish products •Resealable wax case. SPECS Yellow for snow temperatures 0C- -6C (32F-21F) Red for snow temperatures -4C- -12C (25F-10F) Blue for snow temperatures -10C- -30C (14F- -22F)
Toko Jetstream Bloc
$114.99 $229.99 50% Off
This 100% RACING WAX TECHNOLOGY Bloc rub-on is used as a Top Finish Coat in racing and offers top gliding features and improved abrasion-resistance. •Suited for all types of snow regarding the physical meteo-data such as snow temperature and humidity •Remarkable acceleration and higher final speed •Improved long term performance thanks to high abrasion-resistance •Thanks to optimized particle size easy to iron or cork in Weight 20g JetStream Bloc 2.0 Blue Air Temp. -22 to 18f JetStream Bloc 2.0 Red Air temp.11-28f JetStream Bloc 2.0 Yellow Air Temp. 25-50f
Toko Jetstream Powder
$124.99 $249.99 50% Off
100% RACING WAX TECHNOLOGY Toko JetStream Powder 2.0 Wax that can either be ironed or corked in for remarkably increased acceleration, glide and long-term performance. FEATURES Suited for all types of snow Remarkable acceleration & higher final speed High abrasion resistance for improved long-term performance Optimized particle size that is easy to iron or cork in Size: 30g bottle
Swix CeraF FCX Powder
$134.50 $269.00 50% Off
- Swix's Cera F wax is a pure fluorocarbon specially formulated for use on ski bases. - Extremely low surface tension, high resistance to dirt absorption, and very high water repellancy. - Works very well in a wide range of conditions and temperatures. - Sold in 30g powder. FC4X Green -10°C to -20°C (14°F to -4°F) FC5X Turquoise -3°C to -15°C (27°F to 5°F) FC6X Blue -1°C to -10°C (30°F to 14°F) FC7X Violet +2°C to -6°C (36°F to 21°F) FC8X Red +4°C to -4°C. (39°F to 25°F) FC10X Yellow 0°C to +15°C (32°F to 59°F)
Swix HF 180g Glide Wax BULK
$130.00 $260.00 50% Off
Swix’s HF (Hight Fluorocarbon) line of hot wax is a time-tested and proven glide wax for top performance racing. Recommended as base layer for Pure Fluoro top layers.180g. HF04X Green-12°C to -32°C (10°F to -26°F)Recommended iron temp: 155°C (311°F) HF05X Turquoise -8°C to -14°C (18°F to 7°F). Recommended iron temp: 150°C (302°F). HF06X Blue -5°C to -10°C (23°F to 14°F). Recommended iron temp: 145°C (293°F) HF07X Violet -2°C to -8°C (28°F to 18°F). Recommended iron temp: 140°C (284°F). HF08X Red -4°C to 4°C (25°F to 39°F). Recommended iron temp: 130°C (266°F). HF10X Yellow 0°C to 10°C (32°F to 50°F). Recommended iron temp: 120°C (248°F).
Swix HF 40g Glide Wax
$39.99 $79.99 50% Off
Swix’s HF (Hight Fluorocarbon) line of hot wax is a time-tested and proven glide wax for top performance racing. Recommended as base layer for Pure Fluoro top layers. 60g. HF04X Green-12°C to -32°C (10°F to -26°F)Recommended iron temp: 155°C (311°F) HF05X Turquoise -8°C to -14°C (18°F to 7°F). Recommended iron temp: 150°C (302°F). HF06X Blue -5°C to -10°C (23°F to 14°F). Recommended iron temp: 145°C (293°F) HF07X Violet -2°C to -8°C (28°F to 18°F). Recommended iron temp: 140°C (284°F). HF08X Red -4°C to 4°C (25°F to 39°F). Recommended iron temp: 130°C (266°F). HF10X Yellow 0°C to 10°C (32°F to 50°F). Recommended iron temp: 120°C (248°F).
Swix HVC Cold Liquid Topping Wax
$149.99 $299.99 50% Off
As a general rule, works best in older snow Greatest improvement in glide happens when humidity is over 70% Felt applicator is easy to use, even with gloves on One bottle is enough for 10-12 pair skating skis, 13-15 pair of classic skis or 6 alpine skis 50ml bottle
Swix Uni Turbo 100% Fluorocarbon Block
$115.00 $230.00 50% Off
Swix's most universal and most convenient pure fluoro. Apply by rubbing on to prepped glide surface, leaving a thin film of powder. Move very hot iron over the base briskly to melt the powder, adhering it to the base. Brush out gently with a horsehair brush or buff out with a felt pad and go ski. Excellent durability and and top-end speed for long outings or racing. Solid fluoros are a economical alternative to powders as the waxer has more control of application. 20g. 25F-39F.
Swix Warm Turbo 100% Fluorocarbon Block
$115.00 $230.00 50% Off
Swix FC8XS Ceraf Turbo Solid Warm -2C/+15C 20g Block
START Functional High Fluor Glide
$79.99 $159.99 50% Off
Start FHF-fluor gliders and finishing waxes are suitable for all snow conditions when humidity is over 75%.
START Functional High Fluor Liquid
$69.99 $139.99 50% Off
Start FHF3 Functional Ultra Humid Liquid is suitable for all snow conditions when humidity is over 75%. Start FHF1 Functional Ultra Wet Liquid is suitable for all snow conditions when humidity is over 75%.
START Functional High Fluor Powder 30g
$132.00 $264.00 50% Off
Start FHF5 Functional Ultra high fluor powder is suitable for all snow conditions when humidity is over 75%. Start FHF5 Functional Ultra high fluor powder is suitable for all snow conditions when humidity is over 75%.
Page 1 of 2 Next page